Close-out sale on Speich BH500 - BH1200 wiper blades! 35% off until they're gone!

Marine & Construction Supplies
  • Home
  • Shop
  • PRODUCT LINES
    • Product Lines
    • Cen-Tex
    • Baier
    • Deansteel
    • Speich
    • Sprague
  • FAQ
  • ONLINE BILL PAY
  • More
    • Home
    • Shop
    • PRODUCT LINES
      • Product Lines
      • Cen-Tex
      • Baier
      • Deansteel
      • Speich
      • Sprague
    • FAQ
    • ONLINE BILL PAY
  • Sign In
  • Create Account

  • Orders
  • My Account
  • Signed in as:
  • filler@godaddy.com

  • Orders
  • My Account
  • Sign out
Marine & Construction Supplies
  • Sign In
  • Create Account

  • Orders
  • My Account
  • Signed in as:
  • filler@godaddy.com

  • Orders
  • My Account
  • Sign out

Signed in as:

filler@godaddy.com

  • Home
  • Shop
  • PRODUCT LINES
  • FAQ
  • ONLINE BILL PAY

Account


  • Orders
  • My Account
  • Sign out

  • Sign In
  • Orders
  • My Account

Hatch #222

Flush Water-Tight with Spring, Bottom Operated Dogs

image139

Hatches can be made from the following materials:
•  A36 mild (carbon) steel with these finishes:

  • Shop cleaned (SP3) and red-oxide primed. This is our standard finish.
  • Sandblasted to white metal (SP10) and primed with an inorganic zinc primer. Cathacoat 302 (also known as Devoe 302) is the primary inorganic zinc primer we use. This is a premium finish available at an additional cost.
  • Specialized paint / primer finishes are available at an additional cost. Custom paints may significantly increase the product price, since the paint systems cannot be re-used on other jobs.
  • Galvanizing is another premium finish available at an additional cost. This finish option also adds at least two weeks to the lead time.

 •  Grade 5000 series Aluminum 

 •  304 Stainless Steel 

 •  316 Stainless Steel


Hatch cover features: (any material)
• 5/16” thick (for ABS Grade) or thicker if needed

• OPTIONAL: Hatch cover can be insulated with a 2” thick layer of ceramic fiber or mineral wool, or fiberglass insulation behind a 10ga panel of sheet metal

• Ceramic fiber or mineral wool are great for insulating for heat 

• Fiberglass insulation is great for insulating for heat or cold

 
Coaming dimensions:
• 3/8” thick = Steel, Aluminum, or Stainless Steel

• Minimum coaming height: 6”

• NOTE: a 1 inch diameter or larger drain must be installed in coaming by customer to prevent accumulation of water around hatch cover. Failure to install a drain can lead to corrosion of coaming, which may eventually cause hatch to leak. Coupling for drain can be installed by the manufacturer if customer indicates on a drawing the desired location for the drain.


Corner radius:

• 6” diameter on clear opening


Individual Dogs:

• Dogs available in cast aluminum with a stainless steel dog stud, and cast bronze with a bronze dog stud.

• NOT operable from topside of hatch; ONLY operable from below

• Used for applications where security is a concern

• Also useful in higher pressure applications - no penetration through the scuttle cover means there are no pathways for leaking


Dog Handing:

• Dog handles are interchangeable - there is no right-hand or left-hand for flush individual dogs

• Check out our video on how to determine dog handing


Spring Assist Hinge:

• 48” x 48” is the maximum cover size in A36 steel that will work safely with a spring assist hinge

• 60” x 60” is the maximum cover size in Aluminum that will work safely with a spring assist hinge

• 17-7 Stainless alloys are used for the spring wire. All hatches made after 2006 come with Stainless Steel springs. These alloys will experience some rust bloom, and will pull a magnet. The only steel alloy that will NOT rust or pull a magnet is 316 stainless.

• It is possible to put enough spring hinge assemblies with the proper tension to lift a larger hatch cover. However, once the cover is raised more than about 15 degrees, the springs will take over, ripping the hatch cover out of the hands of the person(s) opening the hatch, and will not stop until it hits the end of the safety chains. There is a potential to injure the people opening the hatch, and damage the spring-assist hinge mechanisms in the process.


Gaskets:
• 30 +/- 5 Durometer extruded neoprene, 3/4” x 1-1/4”

• Computing gasket length 


ABS Type Approval / Classing Agency Approval:
• All doors are built to standards generally accepted by ABS, USCG, and other classing agencies. 

• Doors do NOT carry ABS “Type” approval. For further explanation, click here.

• Drawings and release letters are available for submission for classing agency review.

• It is the responsibility of the customer to verify which certification requirements (i.e. ABS, USCG, DNV, SOLAS) apply to their vessel, and to check with their local governing agency as to the requirements for certifications for all of the items quoted, based on the use for each item on the vessel, and the location of each item as installed on the vessel. Depending on the requirements of the governing agency, additional testing at the manufacturing plant may be required. A separate fee will be charged for any testing.

• Doors conform to C-class fire rating - they are made of non-combustible materials, however, they are NOT designed or certified to resist the passage of fire from one space to another. 

For additional information download our pdfs and watch our videos

REFERENCES

CEN-TEX spare parts

SHOP NOW

Copyright © 2020 Marine & Construction Supplies - All Rights Reserved.


We are wholesale distributors and do not maintain a retail space. Any in-person consultations are by appointment only.

  • FAQ
  • TERMS
  • ONLINE BILL PAY