Close-out sale on Speich BH500 - BH1200 wiper blades! 35% off until they're gone!
Signed in as:
filler@godaddy.com
Hatches can be made from the following materials:
• A36 mild (carbon) steel with these finishes:
• Grade 5000 series Aluminum
• 304 Stainless Steel
• 316 Stainless Steel
Hatch cover features: (any material)
• 5/16” thick (for ABS Grade) or thicker if needed
• OPTIONAL: Hatch cover can be insulated with a 2” thick layer of ceramic fiber or mineral wool, or fiberglass insulation behind a 10ga panel of sheet metal
• Ceramic fiber or mineral wool are great for insulating for heat
• Fiberglass insulation is great for insulating for heat or cold
Coaming dimensions:
• 3/8” thick = Steel, Aluminum, or Stainless Steel
• Minimum coaming height: 6”
• NOTE: a 1 inch diameter or larger drain must be installed in coaming by customer to prevent accumulation of water around hatch cover. Failure to install a drain can lead to corrosion of coaming, which may eventually cause hatch to leak. Coupling for drain can be installed by the manufacturer if customer indicates on a drawing the desired location for the drain.
Corner radius:
• 6” diameter on clear opening
Individual Dogs:
• Dog assemblies available with cast aluminum dog handles with a stainless steel dog stud, and cast bronze dog handles with a brass dog stud.
• Operable with a hex wrench from topside, with direction arrows to indicate open position
• For hatches made before February 2015, dog stud head had a slotted head instead of a hex head. T-wrenches are required for operating t-slot dog studs from topside.
Dog Handing:
• Dog handles are interchangeable - there is no right-hand or left-hand for flush individual dogs
• Check out our video on how to determine dog handing
Spring Assist Hinge:
• 48” x 48” is the maximum cover size in A36 steel that will work safely with a spring assist hinge
• 60” x 60” is the maximum cover size in Aluminum that will work safely with a spring assist hinge
• 17-7 Stainless alloys are used for the spring wire. All hatches made after 2006 come with Stainless Steel springs. These alloys will experience some rust bloom, and will pull a magnet. The only steel alloy that will NOT rust or pull a magnet is 316 stainless.
• It is possible to put enough spring hinge assemblies with the proper tension to lift a larger hatch cover. However, once the cover is raised more than about 15 degrees, the springs will take over, ripping the hatch cover out of the hands of the person(s) opening the hatch, and will not stop until it hits the end of the safety chains. There is a potential to injure the people opening the hatch, and damage the spring-assist hinge mechanisms in the process.
Gaskets:
• 30 +/- 5 Durometer extruded neoprene, 3/4” x 1-1/4”
ABS Type Approval / Classing Agency Approval:
• All doors are built to standards generally accepted by ABS, USCG, and other classing agencies.
• Doors do NOT carry ABS “Type” approval. For further explanation, click here.
• Drawings and release letters are available for submission for classing agency review.
• It is the responsibility of the customer to verify which certification requirements (i.e. ABS, USCG, DNV, SOLAS) apply to their vessel, and to check with their local governing agency as to the requirements for certifications for all of the items quoted, based on the use for each item on the vessel, and the location of each item as installed on the vessel. Depending on the requirements of the governing agency, additional testing at the manufacturing plant may be required. A separate fee will be charged for any testing.
• Doors conform to C-class fire rating - they are made of non-combustible materials, however, they are NOT designed or certified to resist the passage of fire from one space to another.
Copyright © 2020 Marine & Construction Supplies - All Rights Reserved.
We are wholesale distributors and do not maintain a retail space. Any in-person consultations are by appointment only.